How to make Diesel cutting machine cutting precision minimized?

       Before examining factors Diesel-powered cutters cutting precision, we need to briefly explain the working principle of steel cutting machine, which is by the motor via a belt drive growth, make high-speed rotation tune straight through the transfer will be transferred straight steel straight, straight mold remove rust by steel surface of the skin, then motor through another pair of belts and gear box reduction effect, while you can drive two transport roller, traction bars forward movement, while you can crank wheel drive so that the hammer up and down motion.
       This process, when the reinforcing bars until a predetermined length, hammer hammering on the turret, Diesel cutting machine can be successfully cut. In order to be able to complete the cycle when the device action, cutting steel falls by rack, since the spring action, knife sets general will return to its original position. This is the basic workflow steel cutting machine, then the impact of steel cutting machine cutting precision of factors?
       First, the base material of different materials steel is the most fundamental factors for the steel cutting machine equipment, even the same material, if the composition of the material of different cutting accuracy will vary. Second, the impact of different diameter steel base material size on the cutting accuracy can not be ignored, because of different diameter steel cutting precision allowed deviation is completely different.
       In addition, different construction sites require precision steel processing will be different, which is also one of the steel cutting machine cutting precision factor. In fact, when the actual control of the operator of such equipment, the effect of skilled staff work between employees and unskilled will have a very significant difference, which directly relates to Diesel cutting machine function achieve what cutting accuracy.

Diesel cutting machine，Diesel Powered Cutting Machine，Portable Cutting Machine: Diesel cutting machine formal method of operation...

Diesel cutting machine，Diesel Powered Cutting Machine，Portable Cutting Machine: Diesel cutting machine formal method of operation...: Before using the first Diesel cutting machine  must be sure the work surface and the cutter is not kept below the level of the state, if ...

Diesel cutting machine formal method of operation

Before using the first Diesel cutting machine  must be sure the work surface and the cutter is not kept below the level of the state, if not, the first thing to do is to adjust the level, then check the cutter steel cutter There are no abnormal phenomenon, for example, there is no crack crack, screw fastening tool is not, but also turned by hand at the pulley, check the top of the backlash is not appropriate, and if we find inappropriate, first adjust better.
Plug in the power, the start time, do not worry now operating on steel, should first dry run for a while, take a look at every part of the operation is not a normal Diesel cutting machine , to determine a good no anomalies, then you can really start operate. In the cut material time, pay more attention to the correctness of the staff is a hand operation, and posture on. Middle and lower use of steel cutting machine should cutter, hand grip bars to the staff, and aligning the entrance of the cutter. If you are a person to operate it, the staff must be fixed position, can only stand on the side of the blade and hard pressed steel, in the course of their work should not arbitrarily change position, to avoid wounding steel.
If the Diesel cutting machine can not be more than a one-time cut rebar, then do not do it abruptly, range of different steel cutting machine has a work must be able to ensure the safety of staff inside the operating range.

Diesel cutting machine rules

1. Shuttle countertop material should maintain the level and lower cutter, table length can be determined according to the length of the workpiece.

2. Before you start, you should check to make sure no cracks cutter, turret bolt, solid shield. Then rotate the pulley by hand to check the gear meshing clearance, adjust the cutter gap.

3. After starting, you should first dry run, check after each transmission parts and bearings in normal operation only after the job.

4.Cyq50a Diesel Powered Cutting Machine does not reach normal operating speed may not cut material. When cutting, use the cutter, the lower parts of the alignment edge grip reinforced quickly put, the operator should stand on the side of force to suppress the fixed blade steel, should be reinforced to prevent the end of the pop-up hurt. It is prohibited on both sides of the blade with both hands holding the steel sub-leaning feeding.

5. Can not cut diameter and strength than steel and red-hot steel mechanical nameplate. Once cut off when a plurality of reinforcement, the total cross-sectional area should be within the specified range.

6. When Cyq50a Diesel Powered Cutting Machine, replace the high hardness cutter, cutting machine plate diameter should be consistent with the provisions.

7. When cutting short material, distance between the hand and the knife should be maintained at 150mm or more, such as when hand side is less than 400mm, should be reinforced short sleeve or jig head pinched or folder in prison.

8. Operation, prohibited by hand directly decapitation and remove debris near the cutter. Rebar cutter swing around and around, can not stay non-operators.

9. When they find machinery not functioning properly, abnormal noise or skew cutter, you should immediately downtime.

10. After the operation, steel brush to remove debris between the cutter, carry out the whole cleaning lubrication.

11. Hydraulic fluid front cutter Diesel cutting machinejob, check that the hydraulic oil and motor rotation direction to meet the requirements. After starting, it should load operation, loose open valve, drain the body of the air cylinder net, only for cutting.

12. Manual hydraulic cutting machine before use, oil drain valve should be tightened clockwise, after cutting is completed, immediately unscrew counterclockwise. Jobs, steady hand should be cut off the machine, and wear insulated gloves.

RB-25 Automatic Bending Machine

RB-25 Automatic Bending Machine

GW42D Automatic Bending Machine

GW42D Automatic Bending Machine

Diesel cutting machine，Diesel Powered Cutting Machine，Portable Cutting Machine

CYQ50A Diesel Powered Cutting Machine
Introduction:
CYQ50A diesel rebar cutter is used to cut steel bar for areas without access to power supply specially. It can be applied in construction sites, rebar processing factories, roads and bridges construction. As a specialized steel bar cutting machine supplier, our products can cut plain carbon steel, hot rolled round steel, deformed steel, flat steel and square steel.
Features:
1. It is driven by diesel engine, which enables areas without access to electricity have the possibility to cut steel bar.
2. Diesel rebar cutter is with good lubricating performance and can work for long time.
3. It adopts antifriction bearing which can reduce friction.
Advantages
Specifications of steel bar cutting machine:
Item CYQ50A
Cutting Capacity
Steel Rod ≤Φ50mm
II Rebar ≤Φ40mm
Max Flat Steel 80×18mm
Max Square Steel 40×40mm
Spindle Speed 7rpm
Diesel Motor Model EM190A
Diesel Motor Power
7 KW/12h
7.7 KW/h
Weight 680kg
Dimension(L×W×H)(mm) 1800×520×840
Relate equipments/accessories of diesel rebar cutter:
It is composed of road wheel, rack, driving structure, machine body, clutch system, blade, etc.